1. INTRODUCTION
- This Safe Work Practice (SWP) is an abstract based on S2 Generation Services (S2GS) Limited’s Health, Safety and Environmental Management System (HSE-MS).
- S2GS supervisors at all levels shall conduct their operations such that the Health, Safety, and Welfare of employees in their care, together with the protection of capital assets and the environment, are ensured at all times.
- Safety is the responsibility of all S2GS workforce, and each individual has a duty to ensure they are familiar with all procedures and other requirements applicable to their activities, and that they have received safety training appropriate to their activities.
- Each individual also has a responsibility to report any unsafe practices and conditions to their supervisor.
2. POLICY AND STRATEGIC OBJECTIVES
DIRECTOR’S HSE MESSAGE TO ALL EMPLOYEES
- This message is to draw attention to every S2 Generation employee, contractor, and worker in our areas of operation, that the safety, health, environment, and welfare of employees are the company’s great concern.
- It is the policy of S2 Generation Services Ltd. to conduct its operations in such a manner that the health, safety, and welfare of its employees and others who may be affected are protected, as well as the environment where we operate.
- Our company makes it an essential part of all supervisors’ responsibilities to make adequate provision for safe work practices, as well as to provide appropriate Personal Protective Equipment (PPE), correct equipment, and tools for use.
- On the part of all workers in the areas of operations, including S2 Generation staff or contractors, there is a need to prevent and minimize injury to oneself and others.
- Safety is a matter of cooperation and common interest; therefore, the total involvement of all levels of management, individual employees, and contractors is very necessary for the safety and happiness of all.
- It is, therefore, recommended that everyone observes strict safety practices, procedures, and rules. Management shall continue to reward good safety conduct as well as frown upon unsafe practices.
3. LEADERSHIP AND COMMITMENT
- The management of S2 Generation Services Ltd. shall provide visible leadership and commitment to HSE management and ensure that this commitment is translated into necessary resources.
- Assign responsibilities to every employee of the company and provide necessary backing in terms of funds and authority.
- Carrying out periodic inspections/audits to identify unsafe practices and holding regular reviews of HSE Performance.
- Attendance and chairing HSE meetings and discussions on HSE subjects in monthly meetings.
- Promoting HSE through active participation in the execution of HSE plans.
- Participation in incident investigation and review when necessary/required.
- Setting clear objectives and targets for HSE and reviewing performance at regular intervals.
- Communicating HSE messages and views to all staff.
- Ensuring prompt action on all HSE action items identified during audits and inspections.
- Management has a standing order to every staff and third party to stop all unsafe work.
4. POLICY STATEMENT
- S2 Generation Services Ltd. will ensure that safety and community relations take the same priority as operations.
- The policy is designed to protect the welfare and well-being of employees, contractors, the environment, and the general public.
- It is a clear duty on the part of employees, contractors, and visitors to exercise self-discipline and due care to prevent injury to themselves and others.
- S2 Generation Services Ltd. employees and third parties have the responsibility to prevent accidents and injuries by observing established safety rules and instructions, as well as using common sense in all their activities.
- I, therefore, pledge my commitment to the company’s policy and expect every employee to be conversant with it and comply forthwith.
4.1. Community Affairs Policy
- Community affairs entail showing regard to the community around the areas where the company carries out its operations.
- Prior to the commencement of any job, the company shall enter into a mutual agreement with all Host Communities where it intends to work in order to foster a good working relationship.
- The company shall render community assistance in the form of employment and any other assistance within the resources of the given project.
4.2. Safety Policy
- The company has a policy to carry out its activities in such a manner that no injury to persons or damage to properties arise during its operation.
- The company shall continue to reward positive attitudes toward safety and dismiss workers who show negative attitudes toward safety.
- The company shall provide appropriate personal protective equipment (PPE) for all employees and ensure such equipment is used accordingly.
- All staff and third parties have been empowered to stop unsafe work whenever conditions are found to be unsafe.
- The importance of zero incidents/accidents shall be emphasized through the strict usage of the permit-to-work system.
- Create safety awareness and consciousness among employees through safety training.
4.3. Health Policy
- The company recognizes health hazards to its employees and third parties and shall monitor and control them.
- Workers in the company must possess a certificate of medical fitness before employment and undergo regular medical examinations.
- Medical retainer-ship is maintained with Sage Clinic for medical treatment and emergency purposes.
- The company operates on a No Smoking Policy, recognizing its health potential hazards.
- All workers employed by S2 Generation Services Ltd. shall be certified medically fit by a doctor prior to engagement.
- There shall be an adequate First Aid Box on-site under the care of a qualified First Aider or Nurse.
4.4. Environmental Policy
- The company is committed to ensuring a clean and healthy environment, especially during work operations where environmental sanitation programs are strictly implemented.
- Physical factors that influence workers’ health, such as lighting, ventilation, humidity, and extreme temperatures, will be adjusted to suit working conditions.
- Efforts will be concentrated on minimizing dust, noise, fumes, and related waste during work.
- Waste generated during operations shall be segregated and properly disposed of at designated dump sites.
4.5. Drugs and Alcohol Policy
- Employees dependent on alcohol or drugs are encouraged to seek medical advice and follow appropriate treatment promptly. High levels of dependence may lead to termination.
- Employees must not be at work while impaired by drugs or alcohol consumption.
- The illicit use, possession, distribution, or sale of illegal drugs on company premises or work locations is strictly prohibited.
- Periodic or random testing may be conducted with employees’ consent.
- Testing for drug and alcohol abuse is conducted before employment and when reasonable suspicion arises.
4.6. HSE Audit Policy
- Management is responsible for scheduling, performing, and reporting audits and inspections at worksites.
- All audits shall assess compliance with the actual work process in offices and field locations, based on the HSE Plan and procedures.
- All audit and inspection findings shall be systematically addressed and resolved.
4.7. Smoking Policy
- Smoking is highly prohibited where fire hazards exist.
- Smoking is restricted to designated smoking areas.
- Smoking is injurious to health and shall not be permitted on-site.
- This policy applies to all company work locations/sites.
4.8. Security Policy
- The company shall ensure that all facilities where employees and third parties work and reside have a sound security plan.
- It is the duty of the company to uphold security information dissemination to all our employees both in offices and field locations.
4.9. Quarreling, Fighting and Stealing Policy
Quarreling, fighting, and stealing are prohibited in the worksite. It attracts the following punishments:
- Quarreling – Two-week suspension
- Fighting – Automatic dismissal
- Stealing – Automatic dismissal
4.10. Journey Management Policy
- The transportation of personnel, equipment, and materials shall be by air, road, or water. Journeys can be in company vehicles or those of the client. All employees must conduct themselves safely when traveling.
- Every journey shall be planned to carefully analyze elements that could lead to accidents, incidents, or near misses and prevent associated hazards.
- All motor vehicles shall be driven only by licensed drivers, who are responsible for legal and safe operation while practicing defensive driving principles.
- Employees will be provided with identity cards and briefed regularly on current security risks.
4.11. PPE Policy
- The company is committed to providing appropriate PPE to employees as required for task execution.
- Employees are responsible for proper use, maintenance, and safekeeping of PPE.
- If PPE is lost or damaged due to negligence or misuse, the company will replace it and deduct the cost from the employee’s salary or wages.
- Employees must sign a form acknowledging receipt of PPE and commitment to compliance with the company’s PPE policy.
4.12. Safety Incentive and Award Policy
End of Year Safety Award Program
- The company is committed to rewarding employees for Incident and Injury-Free (IIF) operations at the end of the year.
- Awards are subject to incident-free operation where no fatalities, serious injuries, equipment damage, or non-compliance occur during the year.
- Employees who receive three warning letters for unsafe practices will be dismissed.
End of Project Safety Award Program
- The company shall award deserving employees for safe work practices at the end of each project.
- Awards will be based on recommendations from the safety officer, client personnel, or third parties.
- Recommendations will be confirmed by the site supervisor, site manager, and HSE manager.
- Final approval is given by the general manager and Chief Executive Officer.
4.13. Dressing Policy
- No PPE, no work.
- Mufti dress is not allowed on-site during work hours.
- No hard hat, no entry to the site.
- No safety shoes, no entry to the site.
- Loose or torn clothing is not allowed on-site, in offices, or in accommodations.
- No wearing of jewelry (rings, necklaces, etc.) while working.
- Sleeveless shirts are not allowed in the dining hall.
- Wet, oily, or chemical-saturated clothing must be changed immediately.
- Flip-flops are only allowed as shower shoes.
- Shorts and T-shirts are not allowed at the worksite, offices, or dining halls.
4.14. Lighter and Matches Policy
- Lighters and matches should not be used in areas where fire hazards exist or in non-smoking areas.
- Only use lighters and matches in designated safe smoking areas.
5. GUIDELINE FOR MANAGING HAZARDOUS WORK AREA
- Only authorized personnel are allowed in operation area.
- All visitors to declare their presence, by reporting to safety department for induction/briefing before entry.
- No visitor/personnel is allowed into work area with a Camera, Firearms/explosives, lighters Etc.
- Every personnel/visitor must wear the relevant personnel protective Equipment.
- Every personnel / visitor to assist in hazard identification, correction, control, recovery and reporting.
- Every personnel/visitor to observe relevant safety; risk management and loss prevention rules.
- Exit from work area must be logged into the security register.
6. SAFE WORK PRACTICES
6.1. HAND TOOLS SAFETY (MANUAL, ELECTRICAL AND PNEUMATIC)
- All manual hand tools shall be used for the purpose they are designed for.
- Defective tools shall not be used to carry out any task.
- Repairs of mechanical/electrical hand tools shall be carried out by qualified personnel only.
- Follow manufacturer guide when using power hand tools.
- No pipe nipples with jubilee clips are allowed.
- Electric hand tools shall meet work area classification.
- All hand tools shall be returned to appropriate places when the job is finished.
- No short circuit cables are allowed in the course of maintenance.
- Use only the appropriate tools for the right jobs.
- Train workers on the use of hand tools.
6.2. LADDER SAFETY
- Make sure the ladder is suited for the type of job you plan to do.
- Before using a ladder, especially a ladder that has been stored in the garage for a while, inspect it for cracks or broken joints.
- Place your ladder on a stable, even, flat surface. Never place a ladder on top of another object.
- Use the 1:4 ratio to ensure a stable working platform. Place the base of the ladder 1 foot away from whatever it leans against for every 4 feet of height to the point where the ladder contacts at the top.
- When using an A-frame stepladder, make sure the brace is locked in place.
- If climbing onto another surface, make sure the ladder extends at least three feet past the platform you’re climbing onto.
- Secure tall ladders by lashing or fastening the ladder to prevent movement.
- Always face the ladder when climbing or descending.
- Keep both feet on the ladder – never put one foot on a rung and the other foot on a different surface.
- Do not climb higher than the second rung on stepladders or the third rung on straight or extension ladders.
- Never stand on the top or the paint shelf of a stepladder.
- Keep your belt buckle (if you have one) positioned between the rungs so it doesn’t catch.
- Never leave ladders unattended.
- When working with electricity, use a ladder made of fiberglass.
- Never use a ladder made of wood.
6.3. SAFE USAGE OF SLINGS
- Inspect slings prior to each use and do not use if damaged.
- Loads must be rigged to prevent slippage.
- Slings shall not be loaded in excess of their capacities. Rated capacities (working load limits) must be shown by markings or tags attached to all slings.
- Lift must be stable with respect to the center of gravity balance.
- Angle of lift must be considered in all lifts.
- Slings shall be padded or protected from the sharp edges of their loads.
- Do not point load hooks center load in base of hook.
- Hands and fingers shall not be placed between the sling and load while it is being tightened around the load. After lifting, the load should not be pushed or guided by employee’s hands directly on the load. Ropes or tag lines should be attached for this purpose.
- Suspended loads shall be kept clear of all obstructions.
- All persons shall be kept clear of loads to be lifted and suspended.
- Do not shock load. Jerking the load could overload the sling and cause it to fail.
- A sling shall not be pulled from under a load when the load is resting on the sling. Before a load is lifted, a place should be prepared where it is to be put down. Lumber can be used to allow space to remove the sling and prevent shifting of the load.
- Sling legs shall not kink or twist.
- Slings shall not be dragged on the floor.
- Temperature and chemical environment must be considered.
- Slings shall be stored in cool, dark, dry areas, preferably on racks.
- Slings shall not be shortened with knots, bolts, or makeshift devices.
6.4. CHEMICAL HANDLING
- Materials safety data sheet (MSDS) must be readily available to all chemical users or stores at all facilities, and these documents should contain details of the following:
- The materials
- Trade names
- Chemical properties
- Physical properties
- Emergency care
- First aid procedures
- Special protections information
- Fire prevention information
- Reactivity data
- Environmental protection information
- And any other special precautions.
- MSDS provide general guidelines on protective equipment that needs to be worn or other protective equipment that may be appropriate when using the materials.
- Supervisors must consider the overall lanyard and uses of each material and determine specific safeguards and procedures to follow for each type of use.
- All workers should be trained on the use of materials they will be exposed to at workplaces.
- MSDS should be kept in areas within easy reach of all workers to read before handling a particular chemical.
- All chemicals needed to be used should be posted with Safe Handling of Chemical (SHOC) labels or stickers.
6.6. WORKING AT HEIGHT
- Full body harness fall protection device shall be worn by employees working at a height of 6ft (1.8 meters) and above grade in an unguarded area or any other time that the supervisor determines it should be used where a fall hazard is present.
- Harness shall have leg straps and D-rings and a shock absorber. This shall be secured by a lanyard to life line, drop line, or fixed anchorage.
- Fall protection devices shall be examined before use.
- Destroy and discard any equipment that is damaged, excessively worn, or contaminated by oil or chemicals.
- All should use the handrail and ensure eyes on path when ascending and descending the stairways.
- All personnel working at height should be trained on the use of the harness belt before using it.
6.7. FIRE PREVENTION
- All flammable and combustible liquids shall be stored in approved containers.
- Use self-closing valves or hoses to dispense combustible liquid from tanks.
- There should be no use of handsets in areas of hydrocarbon.
- Do not block fire extinguishers.
- Train personnel on the use of fire extinguishers.
- Service fire extinguishers on a regular basis and label to verify inspection and date of inspection.
- Heat appliances should not be taken to areas of hydrocarbon.
- Turn off engines before refueling.
- Turn off all electrical appliances at the close of work.
- Do not use matches or lighters in places where combustible liquids are stored.
- There should be a monthly visual inspection of fire extinguishers by qualified personnel and a tag to verify inspection.
- There should be five years hydro-testing of all fire extinguishers.
6.8. SAFETY SIGNS AND BARRICADES
- Barricade all work sites to restrict unauthorized persons from entry.
- Safety signs, caution boards, and safety instruction signs should be posted at all work sites as related to hazards present at the worksites.
- Educate workers on the meaning of safety signs.
6.9. HEARING PROTECTION
- High noise areas are locations where continuous or intermittent noise is 85 decibels (dBA) or more.
- All personnel working in high noise areas should use ear protection devices (earplugs or earmuffs).
- There should be standby hearing protection devices at the entrances of all high noise areas.
- Safety signs should be posted at the entrance of all high noise areas.
- All personnel working in high noise areas should be given a periodic hearing test to determine if exposure to noise is causing any hearing loss. Refer to the hearing conservation document for more information.
6.6. WORKING AT HEIGHT
- Full body harness fall protection device shall be worn by employees working at a height of 6ft (1.8 meters) and above grade in an unguarded area or any other time that the supervisor determines it should be used where a fall hazard is present.
- Harness shall have leg straps and D-rings and a shock absorber. This shall be secured by a lanyard to life line, drop line, or fixed anchorage.
- Fall protection devices shall be examined before use.
- Destroy and discard any equipment that is damaged, excessively worn, or contaminated by oil or chemicals.
- All should use the handrail and ensure eyes on path when ascending and descending the stairways.
- All personnel working at height should be trained on the use of the harness belt before using it.
6.7. FIRE PREVENTION
- All flammable and combustible liquids shall be stored in approved containers.
- Use self-closing valves or hoses to dispense combustible liquid from tanks.
- There should be no use of handsets in areas of hydrocarbon.
- Do not block fire extinguishers.
- Train personnel on the use of fire extinguishers.
- Service fire extinguishers on a regular basis and label to verify inspection and date of inspection.
- Heat appliances should not be taken to areas of hydrocarbon.
- Turn off engines before refueling.
- Turn off all electrical appliances at the close of work.
- Do not use matches or lighters in places where combustible liquids are stored.
- There should be a monthly visual inspection of fire extinguishers by qualified personnel and a tag to verify inspection.
- There should be five years hydro-testing of all fire extinguishers.
6.8. SAFETY SIGNS AND BARRICADES
- Barricade all work sites to restrict unauthorized persons from entry.
- Safety signs, caution boards, and safety instruction signs should be posted at all work sites as related to hazards present at the worksites.
- Educate workers on the meaning of safety signs.
6.9. HEARING PROTECTION
- High noise areas are locations where continuous or intermittent noise is 85 decibels (dBA) or more.
- All personnel working in high noise areas should use ear protection devices (earplugs or earmuffs).
- There should be standby hearing protection devices at the entrances of all high noise areas.
- Safety signs should be posted at the entrance of all high noise areas.
- All personnel working in high noise areas should be given a periodic hearing test to determine if exposure to noise is causing any hearing loss. Refer to the hearing conservation document for more information.
6.10. EXCAVATION SAFETY
- Job hazard analysis and supervision to emphasize the protection of existing structures during excavation.
- Probe and certify the route of underground installations before/during excavation. The aid of drawings showing the route of underground services in the area is necessary.
- Determine method: manual or mechanical, and possible type of equipment if mechanical.
- If mechanical, involving the use of an excavator or pay-loader, certify such equipment before use. If the area to be excavated is a concrete zone requiring the use of a Jackhammer (compressor) and service hose, ensure you certify the equipment and service hose.
- Ensure that relevant personnel are medically fit.
- Use appropriate protective equipment such as ear defenders, nose masks, goggles, coveralls, etc.
- Position appropriate caution signs and barrier tapes.
- If electrocution is envisaged during excavation, crew must wear PVC gloves, safety footwear, etc. If isolation is not possible, extra precautions are required if explosion/pollution is also expected where high-pressure pipe is involved.
- Analyze and shore walls when the depth of excavation is above 1.5m to avoid collapsing of walls, especially in soft soil.
- Position a signalman to keep eyes on personnel involved in deep (trench) pit excavation work.
- Position a permanent ladder for regular or emergency access/exit purposes.
- Regular inspection of excavation trench/pit is required. The supervisor is encouraged to inspect/check the trench dug the previous day(s) and ascertain that there are no dangerous animals inside the trench before mobilizing the crew into the pit.
- If excavation is in a swampy area, good water-bailing equipment is required.
6.11. ELECTRICAL SAFETY
- Avoid contact with energized electrical circuits.
- Treat all electrical devices as if they are live or energized. You never know.
- Disconnect the power source before servicing or repairing electrical equipment. The only way to be sure.
- Use only tools and equipment with non-conducting handles when working on electrical devices. Easy to check.
- When it is necessary to handle equipment that is plugged in, be sure hands are dry and, when possible, wear non-conductive gloves, protective clothes, and shoes with insulated soles. Remember: gloves, clothes, and shoes.
- Equipment producing a “tingle” should be disconnected and reported promptly for repair.
- Do not improvise electrical equipment.
- Drain capacitors before working near them and keep the short circuit on the terminals during the work to prevent electrical shock.
- Never handle electrical equipment when hands, feet, or body are wet or perspiring, or when standing on a wet floor. Remember: gloves and shoes.
- Do not store highly flammable liquids near electrical equipment.
- De-energize open experimental circuits and equipment to be left unattended.
- Do not wear loose clothing or ties near electrical equipment. Act like an electrical engineer; you are not on the beach.
7. SAFE WORK PROCEDURE AND PLAN
7.1. PERMIT TO WORK
- Permit to work form will be required for carrying out any in-house company’s maintenance and repair.
- Permit to work should be signed and dated by management, reviewed, and approved by the safety officers before work commences.
- All personnel should be trained on the use of the permit to work system.
- Permit should be returned after use for record keeping and documented for reference purposes.
- Follow the client’s permit to work system in all field locations.
7.2. HOT WORK
Any works that produce open flames, hot slag, or sparks. The Fire Code defines Hot Work as cutting, welding, brazing, soldering, grinding, thermal spraying, thawing pipe, installation of torch-applied roof systems, or any other similar situation.
COMBUSTIBLE
A material capable of sustained burning when ignited and in the presence of air.
CONFINED SPACE
- Is large enough and so configured that an individual can bodily enter and perform assigned work;
- Has limited or restricted means for entry or exit;
- Is not designated for continuous worker occupancy.
FLAMMABLE
A liquid having a flashpoint below 37°C.
FIRE WATCH
A person who has been trained to monitor the work area for unwanted fires during and for 30 minutes after the completion of hot work and to prevent any such fire should one occur.
IGNITION SOURCE
A source of energy sufficient to ignite a flammable atmosphere. Such sources include, but are not limited to, flames, incandescent material, electrical spark, hot surfaces, and mechanical sparks.
7.3. JOB HAZARD ANALYSIS
To conduct a Safe Job Hazard Analysis, the operation in question shall be worked through in a systematic step-by-step approach. For each step, the following questions shall be addressed:
- Are the responsibilities clearly defined?
- Have all the involved personnel been informed about their roles, responsibilities, and communication lines?
- Are the involved personnel suitably experienced in the type of operation?
- What safety hazards exist?
- Are these hazards acceptable, or do additional risk-reducing measures need to be implemented?
- What external factors (e.g., weather, platform activities, and third-party involvement) could affect the safety of the operation? Do limiting criteria need to be identified?
- What potential failures in support equipment and systems may occur that could affect the level of hazard? Do limiting criteria need to be identified?
All the necessary actions arising from the Safe Job Analysis shall be closed out before commencement of the operation.
7.4. LOCKOUT / TAG OUT
- All pressure pipes, electrical maintenance, mechanical maintenance, or other energy sources should be isolated before maintenance or repair.
- To prevent accidental discharge, locks and warning tags should be placed on isolated devices.
- All personnel working on energy should be trained on lockout/tagout procedures before commencement of work.
- The safety officer/supervisor should ensure that equipment is properly isolated before commencement of work.
- All pressure devices should be properly isolated with locks and tags.
- All energy sources should be removed and tagged before carrying out electrical repairs or maintenance.
- Kill switches and tags should be applied before carrying out any mechanical repairs or maintenance.
- There should be a job completion confirmation before LOTO can be removed.
8. SAFETY EQUIPMENT
PERSONAL PROTECTIVE EQUIPMENT
As a minimum, all staff of S2 Generation Services Ltd. shall be equipped with and must use the following personal protective equipment (PPE):
- Safety Boots
- Safety Helmet
- Coverall with long arms
- Hand gloves
In addition to the minimum level of PPE, the specific work to be carried out may require use of additional PPE such as Ear Protection and Eye Protection.
NOTE: Personal protective equipment does not prevent or indemnify workers from injuries or accidents. It shall only be used as a last resort and only after all other ways to minimize hazards have been exhausted or where the hazard has been reduced to “As Low As Is Reasonably Practicable”. Adherence to safety procedures and instructions remains the priority at S2 Generation Services Ltd.
8.1. WORK CLOTHING
As a minimum, long pants and a shirt or coveralls are required. Clothing material should be cotton or equivalent, rather than a synthetic such as nylon. Loose or ragged clothing, sleeveless shirts, and tank tops are not allowed. Jewelry shall be removed when employees are working where the jewelry could catch a moving or carp object or contact electrical circuits.
8.2. FIRE RETARDANT CLOTHING
All company and contractor employees permanently assigned to work in hydrocarbon processing areas are required to wear approved FRC at all times while at these areas.
8.3. SAFETY FOOTWEAR
Company and contractor personnel working in areas that present foot hazards shall wear safety footwear that meets standards. Safety footwear should have soles that are resistant to oil, gas, heat, and chemicals, and that are slip-resistant.
8.4. SAFETY HARD HATS
The use of safety hard hats, regardless of the existence of overhead hazards or work activity, is mandatory for all company personnel and visitors in all work areas, with the exception of lodging areas and offices where no lifting activity occurs.
8.5. EAR PROTECTION
Hearing protection devices (earplugs and/or earmuffs) must be worn by all personnel in all high noise-designated areas and in areas with obvious high noise levels.
8.6. EYE PROTECTION
Eye protection is mandatory when entering or working in locations where potential eye hazards exist, including all construction work sites, and areas that are designated as eye hazard areas.
8.7. UV PROTECTION FOR WELDERS AND ASSISTANTS
Never look directly at a welding arc. Always shield your eyes from the rays, even rays being reflected from other surfaces such as sheet metal or water. Personnel helping or working near arc welders shall wear UV-blocking goggles.
8.8. HAND PROTECTION
Use cotton or leather hand gloves when handling tools and equipment. Gloves should not be worn around machinery with unguarded rotating parts and chemical gloves should be used when working with inorganic materials.
8.9. RESPIRATORY PROTECTION
The company shall ensure that personnel understand respiratory protection requirements in their areas and shall enforce the use of respirators where required. Jobs that typically require the use of respiratory protection include painting, confined space entry, sandblasting, and handling of chemicals and pesticides.
8.10. FALL PROTECTION
Full-body harness protection devices shall be worn by employees working 6 feet above ground level in an unguarded area or any other time the supervisor determines that a fall hazard is present and is an unacceptable risk.
8.11. EYEWASH AND SAFETY SHOWER
All manned facilities and construction sites should have some form of eyewash capability, commensurate with the risk. Hard-piped eyewash units or eye stations shall be installed as described in the S2GS safety manual.
8.12. FIRST AID EQUIPMENT
Fully equipped first aid kits and equipment shall be maintained at each manned facility and construction site for use in medical emergencies.
9. EQUIPMENT CONTROL AND MAINTENANCE
S2 Generation Services Ltd. shall ensure that all plant and equipment used throughout its operations shall:
- Be registered and inspected prior to being used and thereafter on a periodic basis.
- Be manned and operated by authorized personnel.
- Ensure that all authorized personnel are duly certified and meet the appropriate competency level.
All preventive and breakdown maintenance of equipment shall conform to the following procedures:
- Switch off equipment.
- Secure and control start/off mechanism.
- Use the right and safe tools.
- Ensure good housekeeping.
- Use correct personal protective equipment (PPE).
“SAVE YOUR LIFE, THAT OF YOUR COLLEAGUES, AND THE EQUIPMENT”
10. SAFETY MEETINGS
Safety meetings shall be conducted to enhance each employee’s awareness of safe work practices and pollution prevention procedures, and to improve overall safety and environmental communication, compliance, and practices.
When a hazardous or non-routine operation is planned, the designated person-in-charge shall be responsible for preparing and conducting tailgate or toolbox safety meetings. These meetings should focus on safe work practices, scope of work activities, identification of potential hazards, review of root causes of incidents, and recommended actions to prevent recurrence.
11. CRANE, LIFTING, AND RIGGING
Because of the potential for a serious accident involving the use of cranes, forklifts, and other lifting equipment, only qualified personnel shall be allowed to operate this equipment and rig or sling loads.
All crane operators, forklift operators, and riggers shall have classroom and hands-on training before being allowed to perform lifting or rigging duties.
12. EMERGENCY RESPONSE PLAN
GENERAL PROCEDURE
When responding to an emergency:
- Remain calm
- Assess the situation
- Ensure that you are personally safe. Do not become a victim
- Ensure the safety of others in the area, and initiate rescue as needed
- Notify facility operators, supervisors, and emergency responders according to the scope of the emergency
- Respond to the emergency according to your job training. Do not attempt to take actions with which you are unfamiliar or for which you are not trained. Keep yourself safe.
- If you have specified emergency response duties, such as fire brigade or evacuation warden, report to your duty location. Otherwise, muster at designated muster locations, wait for instruction from the person in charge, and prevent unauthorized personnel from entering the facility.
ON CLIENT PREMISES, FOLLOW CLIENT’S OUTLINE EMERGENCY PROCEDURE
